BINDER FDL Serisi Safety Drying Etüvler ( FDL115 )

Safety drying oven

The BINDER FDL 115 with silicone and dust-free inner chamber, as well as symmetric airflow dries specimens containing solvents and thus this safety drying oven meets all EN 1539 requirements

Advantages:

Defined solvent quantity according to EN 1539
Wide temperature range up to 300 °C

Areas of application:

Chemicals
Surface Technology

Features	Customer benefits	Characteristics
APT.line™	Same test conditions throughout the chamber interior Independent of specimen size and quantity	APT.line™ preheating chamber technology for maximum precision Uniform circulation throughout the inner chamber Homogeneous temperature conditions throughout test specimens
Safety concept	Defined solvent quantity Safe standard-compliant drying	Complies with EN 1539: Fresh air monitoring with automatic switchoff Audible and visual alarm Class 2 independent adjustable temperature safety device Safety class IP 33 Easy to replace fresh air filter
Performance feature	Short warm up times Broad range of applications, e.g. coil coating tests	High air exchange rate Monitored air exchange volume Large power reserves Temperature range up to 300 °C
Inner chamber concept	Maximum occupational safety Easy loading and unloading of specimen material Easy to clean	Very tight door closure with 2-point door latch Low heat dissipation due to 60 mm insulation Rack with tilt protection Complete inner chamber made of stainless steel No permanent fixtures Silicone free Viton (FKM) door seal
Controller	Programmable controller with intelligent temperature control and weekly program timer	Convenient operation and documentation
Quality	Reliable devices with long service lives Short delivery times Minimal maintenance and operating costs	Premium quality made in Germany Highly automated series production High-quality materials, state-of-the-art production technology
Unit options and service	Optimal solution for numerous applications BINDER INDIVIDUAL for customer-specific solutions Worldwide BINDER Service	Comprehensive product portfolio: Various options: temperature measurement of the specimen, calibration certificate Control and documentation software APT-COM™ Drying ovens, vacuum drying ovens, climate chambers Worldwide service network

Electronically controlled APT.line™ preheating chamber assuring temperature accuracy and reproducible results

All safety features met according to EN 1539

Temperature range from 5 °C above ambient temperature to 300 °C

MP controller with 2 programs with 10 sections each, or alternatively one program with 20 sections

The time of an individual program step can be set to max. 99.59 hours or 999.59 hours. This adjustment applies to all program sections.

Integrated weekly program timer with real-time function

Adjustable ramp function via program editor

Digital temperature setting with an accuracy of one degree

Elapsed time indicator

Door gasket FKM (for max. temperature of 200 °C / 392 °F)

Replaceable fresh-air filter cartridge. Class F6 (EU6 fine-particle filter for particle sizes 1 μm to 10 μm)

Independent adjustable temperature safety device class 2 (DIN 12880), with visual temperature alarm

Fresh-air monitoring with visual and audible alarm and automatic deactivation of heating

Rear exhaust connector Ø 100 mm (4 inch)

RS 422 interface for use with APT-COM™ DataControlSystem communication software

Units up to 115 liters are stackable

2 chrome-plated racks included

BINDER test confirmation

FDL 115
	Exterior dimensions
	Width (mm)	835
	Height (incl. feet) (mm)	800
	Depth (plus door handle 50 mm) (mm)	685
	Wall clearance, rear (mm)	100
	Wall clearance, side (mm)	100
	Exhaust duct (outer Ø mm)	100
	Steam space volume (l)	156

	Interior dimensions
	Width (mm)	600
	Height (mm)	435
	Depth (mm)	435
	Interior volume (l)	115
	Racks (number standard/max.)	2 / 5
	Load per rack (kg)	20
	Permitted total load (kg)	50
	Weight (empty) (kg)	90

	Temperature data
	Temperature range approx. 5 °C above ambient temperature to (°C)	300
	Temperature variation
	at 70 °C (± K)	1,5
	at 150 °C (± K)	2,5
	at 300 °C (± K)	4
	Temperature fluctuation (± K)	0,3
	Warm-up time 1)
	to 70 °C (min.)	7
	to 150 °C (min.)	17
	to 300 °C (min.)	44
	Recovery time after doors were open for 30 sec. 1)
	at 70 °C (min.)	1
	at 150 °C (min.)	3
	at 300 °C (min.)	6

	Ventilation data
	Ventilation (approx. x/min.)	3
	Air circulation (approx. x/min.)	40
	Exhaust air volume flow (approx. l/min. m³/h)	400 (24,0)
	Air flow velocity (m/sec)	0,8 - 1,2
	Highest permitted solvent quantity (at T-180 °C, M-100g/mol, U-40g/m3, K=0.5) (g)	6,65

	Electrical data
	IP protection class acc. to EN 60529	IP 33
	Voltage (± 10%) 50 / 60 Hz (V)	230
	Nominal power (kW)	2,9
	Energy consumption
	at 150 °C (W)	1098

1)
T = drying temperature
M = molecular mass
U = lower explosion limit
K = solvent vapor concentration as percentage of lower explosion limit

2) To 98% of the set value

OPTIONS
Access ports with silicone plug, 10, 30 mm	O
Rack,chrome-plated or stainless steel	O
Perforated shelf, stainless steel	O
Door lock	O
Door gasket made of of high temperature resistant silicone for operating temperatures > 200 °C	O
Specimen temperature display with clip temperature sensor and 4 - 20 mA analog output (e.g. chart recorder connection), accessible via 6-pin DIN socket	O
Calibration certificate, measurement in center of chamber at 150 °C or at specified testing temperature	O
Extension to calibration certificate. Each additional measurement at additional measuring point or testing temperature	O
Temperature measurement acc. to DIN 12880 (27 measuring points) at 150 °C or at specified temperature with measuring protocol and certificate	O
Replacement air filter (class F6/EU6 – for particle sizes between 1 μm and 10 μm), 100x520x22 mm 3.94x20.47x0.87 inch), with aluminum frame	O

« Etüvler